SLXD4Q+ Quad Receiver

<System RF></System RF> <Working Range>100 m (328 ft) Note: Actual range depends on RF signal absorption, reflection and interference.</Working Range> <Image Rejection>Greater than 85 dB, typical</Image Rejection> <RF Sensitivity>−97 dBm at 10-5 BER</RF Sensitivity> <></> <System Temperatures>Note: Battery characteristics may limit these ranges.</System Temperatures> <Operating Temperature Range>-18°C (0°F) to 50°C (122°F)</Operating Temperature Range> <Storage Temperature Range>-29°C (-20°F) to 74°C (165°F)</Storage Temperature Range> <></> <System Audio></System Audio> <Latency>3.2 ms</Latency> <High-Pass / Low Cut Filter>150 Hz @ -12 db/oct Note: Factory default is for the HPF to be off</High-Pass / Low Cut Filter> <Audio Dynamic Range>118 dB at 1% THD, A-weighted, typical</Audio Dynamic Range> <Total Harmonic Distortion>Less than 0.02%</Total Harmonic Distortion> <System Audio Polarity>Positive pressure on microphone diaphragm produces positive voltage on pin 2 with respect to pin 3 of XLR output and the tip of the 6.35 mm (¼ inch) with respect to the ring of the 6.35 mm output.</System Audio Polarity> <Mic Offset Range>0 to 21 dB (in 3 dB steps)</Mic Offset Range> <></> <SLXD4Q+ Receiver></SLXD4Q+ Receiver> <Dimensions>42 x 393 x 152 mm (1.65 x 15.47 x 5.98 in.), H x W x D</Dimensions> <Weight>1750 g, without antennas</Weight> <Housing>Galvanized Steel</Housing> <></> <Power Requirements></Power Requirements> <15 V @ 1.03 A with Dante; 15 V @ 0.9 A without Dante>RF Input</15 V @ 1.03 A with Dante; 15 V @ 0.9 A without Dante> <Spurious Rejection>Greater than 75 dB, typical</Spurious Rejection> <Connector Type>BNC</Connector Type> <Impedance>50 Ω</Impedance> <Bias Voltage>15 V DC, 150 mA maximum, per antenna switchable on-off</Bias Voltage> <></> <Audio Output></Audio Output> <Audio Frequency Response>20 Hz– 20 kHz (+1, -2 dB)</Audio Frequency Response> <Gain Adjustment Range>-18 to +42 dB in 1 dB steps</Gain Adjustment Range> <Configuration></Configuration> <1/4" (6.35 mm)>Balanced (Tip = audio +, Ring = audio -, Sleeve = ground )</1/4" (6.35 mm)> <XLR>Balanced (1=ground, 2=audio +, 3=audio −)</XLR> <Impedance></Impedance> <1/4" (6.35 mm)>1.1 kΩ (550 Ω Unbalanced)</1/4" (6.35 mm)> <XLR (line)>500 Ω (250 Ω Unbalanced)</XLR (line)> <XLR (mic)>150 Ω</XLR (mic)> <Full Scale Output></Full Scale Output> <1/4" (6.35 mm)>+12 dBV Unbalanced, +18 dBV Balanced</1/4" (6.35 mm)> <XLR>LINE setting= +18 dBV, MIC setting= -12 dBV</XLR> <Mic/Line Switch>30 dB pad</Mic/Line Switch> <Phantom Power Protection></Phantom Power Protection> <1/4" (6.35 mm)>Yes</1/4" (6.35 mm)> <XLR>Yes</XLR> <></> <Cascade Output></Cascade Output> <Connector Type>BNC; Note: For connection of one additional receiver in the same band</Connector Type> <Configuration>Unbalanced</Configuration> <Impedance>50 Ω</Impedance> <Insertion Gain>0–2 dB, typical</Insertion Gain> <></> <Networking></Networking> <Network Interface>10/100 Mbps, 1 Gbps, Dante Digital Audio</Network Interface> <Network Addressing Capability>DHCP or Manual IP address</Network Addressing Capability> <Maximum Cable Length>100 m (328 ft)</Maximum Cable Length>