ANX4 Receiver

<Dimensions>1.7” x 19.0” x 11.3” (44 mm x 482 mm x 286 mm)</Dimensions> <Weight>8.6 lb (3.9 kg)</Weight> <Housing>Steel; extruded aluminum (Case Top: Aluminum)</Housing> <Thermal Power Dissipation>Maximum: 61.3 W (209.3 BTU/hr) Idle: 49.2 W (167.9 BTU/hr)</Thermal Power Dissipation> <AC Power Requirements>100 to 240 V AC, 50-60 Hz, 1.4 A max</AC Power Requirements> <DC Power Requirements>11.3 to 16 V DC, 10 A max</DC Power Requirements> <Fuse>T5A</Fuse> <Operating Temperature Range>-18°C (0°F) to 50°C (122°F)</Operating Temperature Range> <Storage Temperature Range>-29°C (-20°F) to 74°C (165°F)</Storage Temperature Range> <></> <RF INPUT></RF INPUT> <Spurious Rejection>Greater than 80 dB, typical</Spurious Rejection> <Connector Type>BNC</Connector Type> <Impedance>50 Ω</Impedance> <Configuration>Unbalanced, passive</Configuration> <Bias Voltage>12 to 13.5 V DC, 150 mA maximum, per antenna. Switchable on-off.</Bias Voltage> <Insertion Loss>0 dB, typical</Insertion Loss> <></> <RF></RF> <RF Carrier Frequency Range>174 – 2000 MHz</RF Carrier Frequency Range> <Working Range>100 m (330 ft) (Note: Actual range depends on RF signal absorption, reflection, and interference.)</Working Range> <Gain Adjustment Range>-18 to +42 dB in 1 dB steps (plus Mute setting)</Gain Adjustment Range> <RF Tuning Step Size>25 kHz, varies by region</RF Tuning Step Size> <Image Rejection>Greater than 90 dB, typical</Image Rejection> <RF Sensitivity, ULX-D>-95 dBm at 10-5 BER</RF Sensitivity, ULX-D> <RF Sensitivity, Axient Digital>-93.5 dBm at 10-5 BER</RF Sensitivity, Axient Digital> <></> <AUDIO></AUDIO> <Latency, ULX-D Standard>Less than 2.9 ms</Latency, ULX-D Standard> <Latency, ULX-D High Density>Less than 3.2 ms</Latency, ULX-D High Density> <Latency, Axient Digital Standard>Less than 2.1 ms</Latency, Axient Digital Standard> <Latency, Axient Digital High Density>Less than 3.0 ms</Latency, Axient Digital High Density> <Audio Frequency Response>20 – 20 kHz (±1 dB)</Audio Frequency Response> <Audio Dynamic Range>124 dB A-weighted (Typical, 20 Hz to 20 kHz, System Gain @ +12 dB)</Audio Dynamic Range> <Total Harmonic Distortion>-6 dBFS, 1 kHz, System Gain @ +12 dB Less than 0.1%</Total Harmonic Distortion> <System Audio Polarity>Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the 6.35 mm (1/4-inch) output.</System Audio Polarity> <></> <HEADPHONE MONITOR OUTPUT></HEADPHONE MONITOR OUTPUT> <Audio Frequency Response>20 – 20 kHz (±3 dB)</Audio Frequency Response> <Configuration>¼-inch / 6.3 mm connector, unbalanced stereo</Configuration> <Impedance>63 Ω</Impedance> <Maximum Signal Level>350 mW</Maximum Signal Level> <Pin Assignments>Tip: Audio +, Left Ring: Audio + Right Sleeve: Ground</Pin Assignments> <></> <DC MODULE></DC MODULE> <DC Input Voltage Range>11.3 to 16 V DC, 10 A max</DC Input Voltage Range> <Protection Modes>Reverse Polarity, Over Voltage</Protection Modes> <Connector Type>4-pin XLR (male) (Note: Shell of the DC inlet connector is connected to Chassis Ground)</Connector Type> <Recommended Cable Gauge>6 feet (or less): 18 AWG (1mm); 7-15 feet: 16 AWG (1.5 mm); 16-25 feet: 14 AWG (2.5 mm) (Note: Total cable length should not exceed 25 feet)</Recommended Cable Gauge> <></> <NETWORKING></NETWORKING> <Network Interface>10/100 Mbps, 1 Gbps, Dante Digital Audio</Network Interface> <Network Addressing Capability>DHCP or Manual IP address</Network Addressing Capability> <Maximum Cable Length>100 m (330 ft)</Maximum Cable Length>